Accumulator Spheres, Valves & Switches

This is the warning plate that is attached to both of the brake accumulator spheres.  1966-1980 Silver Shadow, T-series, Shadow II, T-2, Silver Wraith II     

This washer has a number of applications: 1. It is the washer on the choke stove pipe adapters UA5802Z and UE32833 on all cars from 1955 to 1977.2. It is the sealing washer between the Shadow/ T Type brake pressure switches and valve bodies - 2 washers...

This is the accumulator return hose for the Right Hand (A bank) brake accumulator. 1977-1980 Silver Shadow II, Wraith II, T2 models, Camargue & Corniche from VIN 30000 onward

These are the bushes that the operating shaft (UR16887) runs on. They sit just behind the outer shaft o rings (UR10832). Note: 2 Bushes per height control / 4 per car (Sold Each) 1966-1980 Silver Shadow, T-series, Silver Wraith II, Shadow II, Corniche

This is the high pressure pipe between the rear brake pump and the rear accumulator.  1973-1980: Rolls-Royce Camargue (14674-26708) & Corniche (12346-35878) Phantom, Silver Shadow II Saloon (30001-41601) Silver Shadow Saloon...

This is the plunger for the pressure switch. Each car needs 1 per Brake Pressure Switch UD18723. NOTE: Ensure you order these parts when ordering the plunger UD18721 Diaphragm XB1078R Washer  1966-1980  Silver Shadow, T-series,...

This little O ring/seal fits several different parts on your car.(Brakes, Flagstaff, Accumulator, fuel system, air condition) Please inquire with our staff for specific use or reference attached diagrams.  1966-1980  Silver Shadow, T-series,...

This is the high pressure steel braided hose from the front brake accumulator to the body of the car. It is only fitted to Shadow II and T2 models (after VIN 30000) where the front accumulator is mounted on the right side of the engine. 1977-1980 (VIN...

This is the rubber diaphragm inside the brake pressure switch. 1966-1980  Silver Shadow, T-series, Shadow II, T-2, Silver Wraith II   

This is a clamping washer for the accumulator plate. 1966-1980 (VIN 1001 to 41601)   

This is the boot that goes onto the brake pressure switch. 1966-1980 Silver Shadow, T-series, Shadow II, T-2, Silver Wraith II  

This is the brake light switch for all models from 1945 to 1977.  This is a good used switch.  Will have a $50 core charge as this will be sold on an exchange basis.  Exchange means you will send in yours in "rebuild-able" condition...

This is the seal kit to reseal one of the brake accumulator valve bodies for the RR363 systems.  1966-1980 Silver Shadow, T-series, Silver Wraith II, Shadow II, Corniche

This is a new Brake Accumulator Sphere.  There are two required per car and sold each. This is a recently developed accumulator sphere, that is suitable for both the Series I and Series II models. Genuine accumulator spheres are no longer...

This is the o ring between the brake accumulator sphere and the valve body. It is supplied as part of RH2435 and is also supplied with our reconditioned spheres and valve bodies. 1966-1980  Silver Shadow, T-series, Shadow II, T-2, Silver Wraith II

This is the pin & bobbin inside the Brake Accumulator Valves. 1966-1980 VIN 01001-20754

This is the short bleed nipple suitable for all Silver Cloud/ S Type wheel cylinders, all Silver Shadow, T-series, and Silver Wraith Type rear calipers and accumulator valve bodies. Early Silver Shadow models with solid front brake discs were originally...

This is a fully reconditioned brake accumulator valve body. It is suitable for all Shadow I & T1 models (VIN 26708) which have the inlet for the brake pressure switch in the body.We strongly recommend replacing the accumulator sphere (RH2390)...

This is a fully reconditioned brake accumulator valve body. This valve body is suitable for all Shadow II & T2 models where the brake pressure switches are located on the chassis leg. Please contact us with your chassis number if you are unsure...

This is a brake accumulator sphere seal kit. Please be aware that specialist tools are required to strip the sphere down and that once it has been rebuilt it will need regassing. This kit includes a modified valve which replaces the original metal ball...

This is the low pressure return hose from the brake accumulator sphere and valve to the brake reservoir. There are two of these hoses per car on the series 1 models (before VIN 30000). From VIN 30001 this hose fits to the accumulator valve on the left...