Rear Brakes

This is the Right Rear Brake Caliper assembly. 1966-1975  Silver Shadow, T-series, Shadow II, T-2, Silver Wraith II  (VIN 1001-22117) Core will need to be returned  When returning core, please insure with the shipper and pack with...

This is the right hand rear caliper for all cars from VIN 22118 which are not fitted with a master cylinder. Fits: 1975-1980  (VIN 22118-41686)  

This is the accumulator return hose for the Right Hand (A bank) brake accumulator of the Silver Shadow II & T2 models (from VIN 30000). The hose for the left hand side is UR14201P  PART NUMBER: UR20144 MODEL / CHASSIS...

This is the small spring which retains the handbrake pads.  Note: 1 Per Caliper (Sold Each) Part Number:  CD4100 Model / Chassis Applicability   1966-1980 Silver Shadow I,II,III, T-series, Silver Wraith...

This is the rear hub seal retainer. (Modification for UG12012/3) In 1986 (from VIN 15800 approximately) the last of the carburetor engine models had the rear hub grease seal modified to a PTFE lip seal. This is also now supplied as a modification to all...

This is an outer rear wheel bearing.  Note: In the picture you may think this is rust, it is NOT!  This is a cosmoline spray that protects the part against rust. PART NUMBER: UG13562/3 MODEL / CHASSIS...

This is the inner rear wheel bearing assembly (cup and cone) for all models from 1966 onwards. 1966-1980  Silver Shadow, T-series, Shadow II, T-2, Silver Wraith II 1980-2003  Silver Spirit, Silver Spur, Mulsanne, Turbo R Pre Arnage 

This is the flexible rubber brake hose for the right hand rear caliper.  this one runs along the rear trailing arm and is the inner (shorter) hose of the two.  The outer hose is CD6248.  These two hoses have been known to swell and block...

This is the rear hub seal.  This seal is be used together with UR70221 as a modification to replaced the original UR12012 & UR12013 Note:  2 Required Per Car (Sold Each) Part Number: UR70222 Model / Chassis...

This is the felt needed when replacing the rear hubs.  Part Number: UR10045 Model / Chassis Applicability   1966-1980 Silver Shadow, T-series, Shadow II, T-2, Silver Wraith II 1980-2003 Silver Spirit, Silver Spur,...

This is the rear hub adjusting nut.  Usually required when changing out brake rotors. When adding the nut you may need to replace O'ring (UG11161) PART NUMBER: UG10154 MODEL / CHASSIS APPLICABILITY   1965-80 (VIN...

This is a complete set of seals to reseal both rear calipers.  This kit fits models WITHOUT a master cylinder.   If you are splitting the calipers in half then you will also need to order two gallery seals (part number GALLERYRR363) per...

This is a complete set of seals to reseal both rear calipers.  Only takes 1 per car / per axle. If you need the later kit see part number (X-CRL,CD5847) for years '75 onward. If you are splitting the calipers in half then, you will need to order...

This is the small rear caliper piston for 1966-1998 All Models  On the early Silver Shadow and Bentley T models (up to VIN 22117) each rear caliper had two of these small pistons and two large pistons (CD6283).On the later Silver Shadows...

This is the rear Brake Rotor from 1966 all the way up to 1987 models.  1966-1980 Shadow, Shadow II, T-1, T-2, Corniche  1981-1987 year models

This is a set of rear brake pads, 1 set required per car. This is an axle set of rear brake pads, complete with pins and clips. Suitable for all cars from approximately 1966 - 1994  1966-1980 Silver Shadow, Shadow II, Silver Wraith II, Corniche,...

Hub o'ring for the rear hub. PART NUMBER: UG11161 MODEL / CHASSIS APPLICABILITY   1965-80 (VIN 1001-41686) 1980-98 (From VIN 1001 onwards)  

This is the flexible rubber brake hose for the left hand rear caliper.  This hose runs along the rear trailing arm and is the outer (longer) hose of the two.  The inner hose is CD6243.  These two hoses have been known to swell and block...

This is the Left Rear Brake Caliper Assembly.  1966-1975  Silver Shadow, T-series, Shadow II, T-2, Silver Wraith II  (VIN 1001-22117) Core will need to be returned  When returning core, please insure with the shipper and pack...

This is the left hand rear caliper for all cars from VIN 22118 which are not fitted with a master cylinder. Fits:  1975-1980  (VIN 22118-41686)  

This is the large rear caliper piston. There are two of these pistons per rear early (pre 1975 approx) caliper. This item is sold individually. 1966-1975 (VIN 1001-22117)  

This is the set of Handbrake Pads, Set, 1 per car 1966-1980 (VIN 1001-41686) 1980-1998 (From VIN 1001 onwards)

This is the caliper gallery seal, which is needed if you plan on breaking apart the actual caliper when rebuilding.  This seal fits in between the two halves.  Early front calipers (for non-vented / solid brake discs) have one gallery seal...

This is the dust cover for the bleeder screw.   These will go to bleed screw part no. UR10967 Note: Sold Each Part Number: UG2427 Model / Chassis Applicability   ALL MODELS        ...

This is the short bleed nipple suitable for all Silver Cloud/ S Type wheel cylinders, all Silver Shadow/ T Type rear calipers and accumulator valve bodies. Early Silver Shadow models with solid front brake discs were originally fitted with the longer...